Question 1:
In resistance heating highest working temperature is obtained from heating elements made of
A.
Nickel copper
B.
Nichrome
C.
Silicon carbide
D.
Silver
Answer: _________
Question 2:
A non-dimensional number generally associated with natural convection heat transfer is
A.
Prandtl number
B.
Grashoff number
C.
Peclet number
D.
Nusselt number
Answer: _________
Question 3:
Method has leading power factor
A.
Resistance heating
B.
Dielectric heating
C.
Arc heating
D.
Induction heating
Answer: _________
Question 4:
The process of heat transfer during the re-entry of satellites and missiles, at very high speeds, into earth?s atmosphere is known as
A.
Ablation
B.
Radiation
C.
Viscous dissipation
D.
Irradiation
Answer: _________
Question 5:
Ajax Wyatt furnace is started when
A.
It is filled below core level
B.
It is filled above core level
C.
It is fully empty
D.
None of the above
Answer: _________
Question 6:
In the indirect resistance heating method, maximum heat-transfer takes place by
A.
Radiation
B.
Convection
C.
Conduction
D.
Any of the above
Answer: _________
Question 7:
Induction heating process is based on which of the following principles?
A.
Thermal ion release principle
B.
Nucleate heating principle
C.
Resistance heating principle
D.
Electromagnetic induction principle
Answer: _________
Question 8:
________ is used for heating non-conducting materials.
A.
Eddy current heating
B.
Arc heating
C.
Induction heating
D.
Dielectric heating
Answer: _________
Question 9:
Which of the following devices is necessarily required for automatic temperature control in a furnace?
A.
Thermostat
B.
Thermocouple
C.
Autotransformer
D.
Heating elements of variable resistance material
Answer: _________
Question 10:
Direct arc furnaces have which of the following power factors?
A.
Unity
B.
Low, lagging
C.
Low, leading
D.
Any of the above
Answer: _________
Question 11:
The electrode of a direct arc furnace is made of
A.
Tungsten
B.
Graphite
C.
Silver
D.
Copper
Answer: _________
Question 12:
In an electric press mica is used
A.
As an insulator
B.
As a device for power factor improvement
C.
For dielectric heating
D.
For induction heating
Answer: _________
Question 13:
In a resistance furnace the atmosphere is
A.
Oxidizing
B.
Deoxidizing
C.
Reducing
D.
Neutral
Answer: _________
Question 14:
By the use of which of the following, high frequency power supply for induction furnaces can be obtained?
A.
Coreless transformers
B.
Current transformers
C.
Motor-generator set
D.
Multiphase transformer
Answer: _________
Question 15:
The temperature inside a furnace is usually measured by which of the following?
A.
Optical pyrometer
B.
Mercury thermometer
C.
Alcohol thermometer
D.
Any of the above
Answer: _________
Question 16:
Radiant heating is used for which of the following?
A.
Annealing of metals
B.
Melting of ferrous metals
C.
Heating of liquids in electric kettle
D.
Drying of paints and varnishes
Answer: _________
Question 17:
Induction furnaces are employed for which of the following?
A.
Heat treatment of castings
B.
Heating of insulators
C.
Melting aluminium
D.
None of the above
Answer: _________
Question 18:
Induction heating takes place in which of the following?
A.
Insulating materials
B.
Conducting materials which are magnetic
C.
Conducting materials which are nonmagnetic
D.
Conducting materials which may or may not be magnetic
Answer: _________
Question 19:
In electric press, mica is used because it is _______ conductor of heat but/and________ conductor of electricity.
A.
bad, good
B.
bad, bad
C.
good, bad
D.
good, good
Answer: _________
Question 20:
In an electric room heat convector the method of heating used is
A.
Arc heating
B.
Resistance heating
C.
Induction heating
D.
Dielectric heating
Answer: _________
Question 21:
Which of the following insulating materials was suitable for low temperature applications?
A.
Asbestos paper
B.
Diatomaceous earth
C.
80 percent magnesia
D.
Cork
Answer: _________
Question 22:
By which of the following methods the temperature inside arcane can be varied?
A.
By disconnecting some of the heating elements
B.
By varying the operating voltage
C.
By varying the current through heating elements
D.
By any of the above method
Answer: _________
Question 23:
Which of the following methods is used to control temperature in resistance furnaces?
A.
Variation of resistance
B.
Variation of voltage
C.
Periodical switching on and off of the supply
D.
All of the above methods
Answer: _________
Question 24:
It is desirable to operate the arc furnaces at power factor of
A.
Zero
B.
0.707 lagging
C.
Unity
D.
0.707 leading
Answer: _________
Question 25:
In an electric room heat convector the method of heating used is Resistance heating
A.
True
B.
False
Answer: _________
Question 26:
Resistance variation method of temperature control is done by connecting resistance elements in
A.
Series
B.
Parallel
C.
Series-parallel connections
D.
All of the above ways
Answer: _________
Question 27:
In heating the ferromagnetic material by induction heating, heat is produced due to
A.
Induced current flow through the charge
B.
Hysteresis loss taking place below Curie temperature
C.
Due to hysteresis loss as well as eddy current loss taking place in the charge
D.
None of the above factors
Answer: _________
Question 28:
Which of the following is an advantage of heating by electricity?
A.
Quicker operation
B.
Higher efficiency
C.
Absence of flue gases
D.
All of the above
Answer: _________
Question 29:
In a domestic cake baking oven the temperature is controlled by
A.
Voltage variation
B.
Thermostat
C.
Autotransformer
D.
Series-parallel operation
Answer: _________
Question 30:
Which of the following will happen if the thickness of refractory wall of furnace is increased?
A.
Heat loss through furnace wall will increase
B.
Temperature inside the furnace will fall
C.
Temperature on the outer surface of furnace walls will drop
D.
Energy consumption will increase
Answer: _________
Question 31:
Which of the following is an advantage of eddy current heating?
A.
The amount of heat generated can be controlled accurately
B.
Heat at very high rate can be generated
C.
The area of the surface over which heat is produced can be accurately controlled
D.
All of the above
Answer: _________
Question 32:
Properly of low temperature coefficient of heating element is desired due to which of the following reasons?
A.
To avoid initial rush of current
B.
To avoid change in kW rating with temperature
C.
Both (A) and (B)
D.
Either (A) or (B)
Answer: _________
Question 33:
Heat is transferred simultaneously by condition, convection and radiation
A.
Inside boiler furnaces
B.
During melting of ice
C.
Through the surface of the insulted pipe carrying steam
D.
From refrigerator coils to freezer of a refrigerator
Answer: _________
Question 34:
For radiant heating around 2250°C, the heating elements are made of
A.
Copper alloy
B.
Carbon
C.
Tungsten alloy
D.
Stainless steel alloy
Answer: _________
Question 35:
Hysteresis loss and eddy current loss are used in
A.
Induction heating of steel
B.
Dielectric heating
C.
Induction heating of brass
D.
Resistance heating
Answer: _________
Question 36:
Which of the following methods of heating is not dependent on the frequency of supply?
A.
Induction heating
B.
Dielectric heating
C.
Electric resistance heating
D.
All of the above
Answer: _________
Question 37:
In arc furnace the function of choke is
A.
To stabilize the arc
B.
To improve power factor
C.
To reduce severity of the surge
D.
None of the above
Answer: _________
Question 38:
Induction heating takes place it which of the following?
A.
Insulating materials
B.
Conducting materials which are magnetic
C.
Conducting materials which are non-magnetic
D.
Conducting materials which may or may not be magnetic
Answer: _________
Question 39:
________ has the highest value of thermal conductivity.
A.
Copper
B.
Aluminium
C.
Brass
D.
Steel
Answer: _________
Question 40:
Which of the following has the highest value of thermal conductivity?
A.
Water
B.
Steam
C.
Solid ice
D.
Melting ice
Answer: _________
Question 41:
Radiations from a black body are proportional to
A.
T
B.
T 2
C.
T 3
D.
T 4
Answer: _________
Question 42:
Properly of low temperature co-eflficient of heating element is desired due to which of the following reasons?
A.
To avoid initial rush of current
B.
To avoid change in kW rating with temperature
C.
Both (A) and (B)
D.
Either (A) or (B)
Answer: _________
Question 43:
The material of the heating element for a furnace should have
A.
Lower melting point
B.
Higher temperature coefficient
C.
High specific resistance
D.
All of the above
Answer: _________
Question 44:
In induction heating __________ is abnormally high.
A.
Phase angle
B.
Frequency
C.
Current
D.
Voltage
Answer: _________
Question 45:
For the transmission of heat from one body to another
A.
Temperature of the two bodies must be different
B.
Both bodies must be solids
C.
Both bodies must be in contact
D.
At least one of the bodies must have some source of heating
Answer: _________
Question 46:
When a body reflects entire radiation incident on it, then it is known as
A.
White body
B.
Grey body
C.
Black body
D.
Transparent body
Answer: _________
Question 47:
Heat transfer by condition will not occur when
A.
Bodies are kept in vacuum
B.
Bodies are immersed in water
C.
Bodies are exposed to thermal radiations
D.
Temperatures of the two bodies are identical
Answer: _________
Question 48:
A perfect black body is one that
A.
Transmits all incident radiations
B.
Absorbs all incident radiations
C.
Reflects all incident radiations
D.
Absorbs, reflects and transmits all incident radiations
Answer: _________
Question 49:
For heating element high resistivity material is chosen to
A.
Reduce the length of heating element
B.
Increase the life of the heating element
C.
Reduce the effect of oxidation
D.
Produce large amount of heat
Answer: _________
Question 50:
Which of the following heating methods has maximum power factor?
A.
Arc heating
B.
Dielectric heating
C.
Induction heating
D.
Resistance heating
Answer: _________
Question 51:
For intermittent work which of the following furnaces is suitable?
A.
Indirect arc furnace
B.
Core less furnace
C.
Either of the above
D.
None of the above
Answer: _________
Question 52:
Due to which of the following reasons it is desirable to have short arc length?
A.
To achieve better heating
B.
To increase the life of roof refractory
C.
To have better stirring action
D.
All of the above
Answer: _________
Question 53:
In direct arc furnace, which of the following has high value?
A.
Current
B.
Voltage
C.
Power factor
D.
All of the above
Answer: _________
Answer Key
1:
C
2:
B
3:
B
4:
A
5:
B
6:
A
7:
D
8:
D
9:
B
10:
B
11:
B
12:
A
13:
A
14:
C
15:
A
16:
D
17:
A
18:
D
19:
C
20:
B
21:
B
22:
D
23:
D
24:
B
25:
A
26:
D
27:
C
28:
D
29:
D
30:
C
31:
D
32:
C
33:
A
34:
C
35:
A
36:
C
37:
A
38:
D
39:
A
40:
C
41:
D
42:
C
43:
C
44:
B
45:
A
46:
A
47:
D
48:
B
49:
A
50:
D
51:
A
52:
D
53:
A